Thursday, February 4, 2016

Flare Prototype.

We have finished the first prototype of the power flare that will be attached to our drone. The structure of the flare is a 3d printed shell that hold s a 9 volt alkaline battery. On the outside of the shell is a string of LED's that display a red flash. The flare will be connected to the drone through servos with 3d printed wings that will suspend the power flare onto the drone and keep it from falling.

Tuesday, January 19, 2016

A.R.C Abstract

A.R.C Abstract


Chances of surviving an avalanche burial if located under fifteen minutes are 92%; These chances are diminished to 30% at thirty five minutes as victims begin to succumb to acute asphyxiation. Currently, avalanche fatalities have been steadily increasing with 324 fatal avalanches killing 440 people in the past 50 years. In the past 30 years, no technological advances in avalanche rescue have been made which have contributed to a decrease of the mortality rates of avalanches.
The goal of the A.R.C(Autonomous Rescue Companion) project is to invent a product which will lead to the decrease of deaths due to avalanche accidents. In order to reach this goal we are taking the approach of being able to locate the victim before rescue teams arrive, thus allowing rescue teams to retrieve the victim in a reduced time span. We are headed towards creating a drone which achieves this. The drone will be able to roughly locate the victim by receiving the signal from their emergency beacon if it is on the skier/hiker’s person. After the drone has approximated the location of the victim, it will then paint the area using an attached spray paint can to apprise the rescue teams of the location.

The final results of A.R.C should lead to a decrease in the rescue time of avalanche teams, thus making victims of avalanches have a greater chance of surviving the accident. This project should conclude with a theoretical decrease in the mortality rates of avalanches.

Monday, January 18, 2016

Flare progress

We have begun working on the design of the flare by first creating a prototype of where the LED's will be placed and will then make a 3d model of the case for the LED's. We are also working on the mechanism for dropping the flare.

New Method

Our new method for informing the rescue team on the victims locations is using a power flare. We will be making an LED flare based on the design of a power flare, (http://pfdistributioncenter.com/). The case for the flare will be 3d printed and inside will be high power LED's that will illuminate the snow and make it easy for the rescue team to find the victim. The flare will be delivered by the drone by a mechanism that will cause the drone to lower near the surface of the ground then drop the flare onto the snow.

Spray Can Update

To lower the amount of voltage needed to push down hard enough to activate the spray can, we attempted to change the type of can to see if it lowers voltage needed. We purchased a small spray can and a large spray can with a attachable trigger to make the can fire easier. When testing to see if the voltage needed to fire the spray can was reduced, the smaller spray can's voltage was not reduced and the attachable trigger did not make it easier to use the spray can. We are moving to a new plan to give the rescue plan the avalanche victims location

Friday, December 18, 2015

What we've done, and what we are doing next


So far we have created two prototypes for the spray can brace. The first one held the solenoid above a spray can. The errors with the first model was that the solenoid was too high and did not reach the spray can, the spray can was also not stable enough, and the holder for the solenoid was to loose. The second model had sides that kept the can in place and the structure was more stable. The solenoid reached the cap but the spray can needs to be better fit to the model. We also need to reduce weight of the brace so that it does not hinder the drone. For the solenoid to press down strong enough on the spray can it must be 16 volts or higher. We now plan on taking with Ryan from Pittsburgh Techshop.

Friday, December 11, 2015

Spray paint Update

Our current model of the brace and solenoid does not have enough power to steadily fire the paint. After talking to our Mr Nasear and Dr Beamer, we decided the best way to solve the issue was to increase the voltage. When testing the solenoid and can on a 30 volt charge it fired much faster and was able to create a continous spray for the can and had more than enough force. Our next challenge is to find a 30 volt battery light enough for us to put on our drone.